ML1400 RSlogix Micro
I was brought the problem at work of an ML1400 PLC being programed with RSLogix micro. They wanted to open and edit the program but only had RSLogix 500 to do so. They said they could download the...
View ArticleFTView SE for SCADA
Hi There, I have an issue with our control system which is based on an Allen-Bradley L33-ER PLC with Allen Bradley Panel PC hosting FactoryTalk View Supervisory Edition for SCADA. Should I post my...
View ArticlePowerflex 700s
Hello help me please , How do I copy the program from compactflash to powerflex 700s ? I lost setting when i switched The device to Factory setting .
View ArticleKeyence IV2 sensor to Allen Bradley PLC
Disclaimer, I do not know much about PLC’s, and am completely stuck on how to proceed, so any help is appreciated! If anyone can help me write very explicitly the ladder logic, you would be an...
View ArticleMicrologix 1400 to Powerflex 523 on DSI
I am trying to communicate power flex 523 drives to micrologix 1400 directly through DSI using 1763-nc01 cable. I have considered channel 0 in plc as modbus RTU master and trying to connect but not...
View ArticlePowerflex 525
Hi We are getting a Ground Fault error F013 consistently (9 times out of 10) when we try to run one of our rolling mills in auto mode. We do not get the issue when we jog forwards in manual. This is a...
View ArticleRSlogix 1200
we have 4 micrologix 1200 plc which i would like to read the data off them IE Amps Temp run time they were set up via a third party to do this but the company is no longer in go i can see the plcs on...
View ArticlePanelView C600
Hi guys, I'm doing a little practice with a Micrologix 1400 and a HMI PanelView C600. The program is so simple. Turn on the output O 0:0 through the input B3 0:0 (START) and turn it off with B3 0:1...
View ArticleClik here to view.
The PC (process complete) bit of MAS command does not clear
Hello everyone, I have this weird problem that the PC (process complete) bit of MAS command does not clear after a cycle time. As you may probably see in the picture attached when the desired torque...
View ArticlePowerFlex DC Drive
I have a PowerFlex DC drive that is causing me some issues. I will preface this by saying I am not a drives guy. Our problem is we ask it to reach a certain speed and it will overshoot for just a...
View ArticleStoring values in RS logix 5000
Hi all, I have an issue where I need to store a value in RS Logix 5000, the initial value is a calculation and the total ends up as F8[6] I need to store this value say "15" somewhere and reset F8[6]...
View ArticleMicrologix 1000 Fault Problem
Would someone be so kind as to document a method to clear a fault on a Micrologix 1000. Does one need programming cable and software or is there another method to clear a fault to see if it returns?...
View ArticleControl Logix connection with HAAS CNC
Hello I am trying to get for HAAS CNC variables eeg. 10800,10801 etc into the PLC. Does anyone know of any ADD ON instructions ? Thank You
View ArticleCreating module in Studio5000
I have a 1734-aentr point i/o ethernet adapter that I’m trying to add to studio 5000. The 1734-aentr is is a C-series with Revision 6 firmware. When I go to “create module” and try to change the...
View ArticleSLC 5/04 Lights are flashing in RUN Mode
I have a friend of mine that just called me from CA. All the lights on the SLC 5/04 are flashing around like the CPU is in infinite reset. They are out in field and dont have the laptop with them When...
View ArticleEthernet/IP bus line topology to ring.
I have an Ethernet/IP bus and system including Ethernet/IP devices with CPU 1756-L81ES ControlLogix. PLC is connected to the switch. Bus is built from the switch as a line. Can I connect the last...
View ArticleClik here to view.
analog output card 1734-OE2V parameters, fault/actions, program mode
I have an analog output card 1734-OE2V and there is in the fault/actions page parameters for program mode. What is program mode and when it is activated? Fault mode is clear but... Program should be...
View ArticleAOP installation broke module RSL5000
Hello, My coworker and I are commissioning a new panel. We have a 1732-AENTR series C remote IO thats Rev 6.1. The project file from a previous identical panel has the module at rev5.3 in the project...
View ArticleClik here to view.
Unknown Extended Error Code
Hey, all. Working on a project using MSG instructions and I'm getting an extended error code and I can't find anywhere what the code means. It's a "create socket" MSG instruction and I am getting...
View ArticlePF527 syncronizing, not connecting
I have two PF527 devices in a bus. These are in the same motion group. If I take the ethernet cable off, it will not connect the PF527 anymore back to the be controlled. I can find it on the net (ping...
View Article