RSLogix5000 Controller Organizer window disapears
Not sure if this was mentioned before and if you may have run into this but I just found about it the hard way and I am not happy about it. Everything was going according to plan until I tried to make...
View ArticleClik here to view.
Unable to add modules to I/O configuration, error 80131940
Hi. I am new to Allen Bradley PLCs and bumped into the following issue, that I cannot find any solution to. When trying to add a module to the I/O configuration I get the attached error, error code...
View ArticleFT View ME Studio 9.0
I am using Studio 5000 V30 and FT View ME Studio 9.0 to develop a solution for my current project. For once I am ahead on the project and have already started developing the basic plc logic and...
View ArticleSLC5/05 in unmatched chassis
I have a spare SLC5/05 chassis with I/O. I want to load a different SLC5/05 program into this processor, but the I/O configuration doesn't match the actual modules. So, how can I run the program...
View ArticleClik here to view.
Cant make runtime application with FTVstudio 7.00
I try to make the runtime application for my Panel view plus 7 when i test the application it works and integrated with the PLC I/O but when i create the runtime application, it comes with messages...
View ArticleClik here to view.
OLD Panelview 1200 replacement
Hi, I'm kind of a newbie at this, but we just replaced a panelview 1200 on a line. But I need to download the program to it. since I couldn't find the old file on our companies computers my thoughts...
View ArticleUpload greyed out in Studio 5000 (after download from other PC)
I made some changes which required me to do a download. Before I took the PLC offline I did a backup. After I was done I wanted to do another backup from my laptop over the network. I opened the...
View ArticleNeed help concern panel view 550 keypad
Hi there. I have panel view 550 keypad . Part number 2711-k5A5 has communication port rs-232 phisically it's protocol dh-485 . Can I replace it with other one has communication port rs-485 phisically...
View Articlehaving issues adding modules to 1734-AENTR
Client is wanting to use a 1734-AENTR with I/O and what not. When I go into the hardware tree to add I/O, its grayed out to add a new module to the hardware tree. JUST for this critter though, has...
View ArticleLogix 500 math instruction with Decimal Point
Hi my problem may have a simple solution but i cant work it out. I need to use the Divide function but it wont let me use a decimal point in either Source A or Source B. Is there a way to use a...
View ArticleLogix 500 math instruction with Decimal Point
Hi my problem may have a simple solution but i cant work it out. I need to use the Divide function but it wont let me use a decimal point in either Source A or Source B. Is there a way to use a...
View Articlehow to use Shift register in Micro 850
I am using micro 850 plc with ccw software. In my program i need to use SHR(shift register) for sequence. but while i used this shift register in array[0..30] .i got warning simple...so how to use...
View ArticleHelp With Replacing Micrologix 1200
I have a machine at work that has a failing Micrologix 1762-L40AWA Series B. I have a 1762-L40AWA Series C unit on hand. I have uploads of the existing unit and want to download the latest to the new...
View ArticleProblem after adding EDS file
Hi Expert, i have problem when adding eds file for module 1769-ASCII 2 Channel. I downloaded EDS file from Rockwell page, then using EDS installing tool to add Module EDS file for version 2.002. But...
View ArticleClik here to view.
Kinetix 5500 - Fault
Hi Guys, I need your various suggestion and helps on this issues. Past few days we facing an issues whereby the gantry of Z-axis which using the Kinetix 5500 servo drive straight crash down on the...
View ArticleClik here to view.
Problem in adding Promass 300 device in RS logix 5000
I try to add Flowmeter device Promass 300 in my RS logix configuration module and Ive got this messsage "Code 16#0009 Module Configuration Rejected: Parameter Error. Additional Fault Code 16#0000"...
View ArticleMicro850 and kinetix3 drive
Hi..every one I am new the AB PLC and servo, I am going to use AB kinetix 3 drive and servo , micro850 plc and ccw software. i got some example program from ab website but i have more droughts on...
View ArticleCCWB connected components work bench
I have compiled a simple UDFB as per tutorial. When I open programs and then then the named UDFB it opens up but not in the correct form. The EN and OUT tags are missing and the first local variable...
View ArticleLogix 5, 500 and 5000 ladder editor color shema
So for years now ive always changed the default color scheme in logix 5, 500 and 5000 from the default white background to black and done some other nifty things with the colors. Really helps my eyes...
View ArticleInjection Molding Press
I've installed several plc's, micrologixs 1200 an 1500's in older injection molding presses in my shop replacing relay logic. I've used the same program as a base line and changed it to adapt to...
View Article