Ultra 3000 Drive Follower not indexing
I have two Ultra 3000 drives with MPL A310F motors. One is setup as "Follower: Auxiliary Encoder". I get the drive enable, follower enable, and both encoder values (motor and auxiliary) but for some...
View ArticleCCW/Micro800 series
Hello all! I have a two part question - both revolve around using Rockwell's CCW software. 1) in rs500 you can mov a value into the an int memory slot and call that int up later on for comp....
View ArticleCounter Malfunction
The Following is the code I question: XIC Local:1:I.Data.0 TON DebounceOnTimer 500 0 XIO Local:1:I.Data.0 TON DebounceOffTimer 1000 0 XIC DebounceOnTimer.DN OTL DebouncedData0 XIC DebounceOffTimer.DN...
View ArticleHi Experts, the pulses counted in my flow meter are not the same with what it...
Hi experts, the pulses counted in my flow meter are not the same with what is counted in my PLC. my flow meter is set at 1 liter per pulse, and the pulse width is 100 mili-seconds my PLC filter is...
View ArticleModbus TCP/IP MVI56 MNETR can not connect
Hi everybody. I want to connect my laptop to module MVI56 MNETR and upload setting then change some information. Module IP: 192.168.1.12. I use Ethernet cable connect to Ethernet port of module and...
View Article1771-OW16 vs 1771-OW16/B rev H01
What is the difference between the 1771-OW16 and 1771-OW16/B rev H01 relay output modules? Can the 1771-OW16/B replace the 1771-OW16 module, or there other constraints? Thanks.
View ArticleFTview 7.0 - how do I make a Macro run a VBA-routine?
I would like a Macro to run a VBA routine (that I wrote for a special purpose). How is that done?
View ArticleScript Rodando Direto
Sera que alguem pode me ajugar, no FactotyTalk, criei um script que le dados da planilha excel, mas isto clicando num botao. Como faco pra deixar este script rodando direto por tras da minha tela sem...
View Articleindradrive problem
Hi gays. I have a problem with my indradrive when I try to jog a Rexroth MSK motor. Indradrive: HCS02 (Basic Universal, single axis), control unit: CSB01.1C-SE-ENS-EN1-L1-S-NN-FW & power...
View ArticleScript Rodando Direto
Urgente. Alguem sabe me dizer como faco para deixar rodando um script por tras da tela toda hora para atualizacao de valores? O script ja tenho, ele busca valores da planilha em excel quando digitado...
View ArticleML1100 And Analogue Expansion Module
Hi Guru's I'm in a bit of a pickle and hoping you can help...... I have a ML1100 with an analogue input/ouput expansion module hanging off it but i can't seem to get the 0 to +10v I:1.0 working i have...
View ArticleScript para obter Dados do Sql para o FactoryTalk
Boa tarde, estou precisando de uma ajuda. Alguém sabe como faco para buscar dados do Sql Server e mostrar este no meu supervisório FactoryTalk? Sabem de algum script para fazer esta leitura? Agradeço...
View ArticleRSView script for SQL queries
Hello I am in charge of a project to put a new solution mixing tank in service and we would like to have a report of time stamps and temperatures automatically generated and saved to a file (preferably...
View ArticleClik here to view.
absolute motion servo motor and emergency stop
Bonjour, Hello, I use a l33erm automaton and a Kinetix servo motor . This servo motor drives an engine with a chain moving in steps of 100 millimetres (there are 15 steps on the chain ) At each top of...
View ArticleCj2m-CPU31_ Allen bradley powerflex 525_Ethernet
Hello, I have Omron plc specifically CJ2m-CPU31 connected to Allen bradley powerflex 525. I wonder what command should i use to drive the frequency inverter and to change the frequency at a certain...
View ArticleDifference between l33erm and 306erm.
Hello I would like to know the Difference between l33erm and 306erm. I could see that the l33erm can have 8 axes against 2 max for l306erm. The memory is higher on l33erm. What are the other...
View ArticleDC Motor Control With Analog out on SLC 5/03 Comments or suggestions?
This is my first Motion control program and one of my first times dealing with analog control in general. I have created (LAD 5 Tensionctrl) in this program to control the speed of a material payoff...
View ArticleAdd-Ons for gas and liquid flow thru an orifice
I converted some of my structured text routines to CLX Add-ons. If anyone is interested I would be happy to share. They are tried and true routines that I've used for years. Both are used for...
View ArticleHelp catching my runaway TLY Servo
Hi All, I have an AB servo TLY-A110T and 2097-V31PR0-LM Kinetix 350 drive. I thought that it was fully configured and ready for tuning, but when I issue a MSO it immediately starts to spin the shaft...
View ArticleClik here to view.
Messaging a PLC 2 over a 1756 DHRIO connection with an L81E
I have been doing some research on data highway and data highway plus, and have contacted Allen Bradley for information regarding communication. We are currently working on a project that involves us...
View Article